superjeans.blogg.se

1. #Colt saa 3rd generation serial numbers serial numbers
2. #Colt saa 3rd generation serial numbers serial number
3. #Colt saa 3rd generation serial numbers full
4. #Colt saa 3rd generation serial numbers free

#Colt saa 3rd generation serial numbers full

As a special order item ColtĪlso has made them with full blue finish.

Also, standard finishes have always been blue with colorĬase hardened frame or fully nickel plated. Generation ones have had these following lengths: 2, 3, 3-1/2, 4, 5, 6,Īnd 12 inches.

However, special order or special run 3rd SAA's have been 4-3/4, 5-1/2, and 7-1/2 inches and such remained Since the late 1870s the three standard barrel lengths for Until 1900 and all the 2nd and 3rd Generation guns are fine for modern Colt did not warranty any SAA for smokeless powder ammunition Second as "smokeless-powder frame." Yet beware those names are Refer to the first style as "black-powder frame" and the Transverse spring-loaded latch standard from then on. Then gradually between 18 Colt phased in the From 1873 until theĮarly 1892 the screw was the method standard for holding the base pin in To the company's website it is not available now.Īnother feature Colt brought back in the 3rd Generation is theĪngled screw in mainframe to secure the base pin. 44 Special was added as an option but according Magnum were standard from the beginning in 1976. Participants desiring low recoil, Colt for a time brought back. With the advent of cowboy action competition and many of their Of those 3rd Generation SAA's in my racks nowħ are chambered for those two dual-digit cartridges. They have doneĪn excellent job of matching barrel and cylinder dimensions with theseįine old cartridges, making them some of the most accurate SAA's

Is Colt resurrected two of my favorite cartridges in them. One reason I lavish my affections on many 3rd Generation SAA's Him smooth their forcing cones as they leave the factory short and Upon buying one I factor in the cost of an action smoothingīy my friend Tom Sargis at Bozeman Trail Arms. Makers' craft, except from the factory their actions are rough toĪn extreme. Mine are excellent examples of the revolver Iįavor those with the split SA in the serial numbers, or simply stated Generation SAA's, after having owned 40 with 10 still on hand. The following is my experience-based opinion concerning 3rd Not so in 3rds until about 2002 when the old Also different is the ratchet at rear of cylinder, mandating aĭifferent rotating hand. Untilġ976 barrel threads were 20 per inch. It this way: parts between 1st and 2nd Generations are interchangeable. According to Colt there is no such thing in regards to thoseĮngineering changes between 3rd Generation and the first two. Now in a sentence let's get this idea of a 4th Generation SAA

#Colt saa 3rd generation serial numbers serial numbers

Worry about what to do with the SA in serial numbers for quite a while. Also there was information Colt was only producing about 80 On the Colt Forum, serial numbers as high as S75XXXA have now been Two thousand numbers were skipped this time Many fans wondered what the company would do when SA99999 was At this point Colt changed the SA fromĪ suffix to a prefix and started again at SA01001.

#Colt saa 3rd generation serial numbers serial number

When production started again inġ976, the 3rd Generation began at serial number 80,000SA and by lateġ978 number 99,999SA was reached. SAA's were out of production for two years while Colt retooledĪnd made some engineering changes. There were no letters in the serial numbers-none Colt began what wasĬalled the 2nd Generation in 1956 at 0001SA and ended circa 1974 at The 1st Generation ran from 1873 until 1941 with serial

After about 1980,įinding fault with their fit became a rare thing.īefore continuing, let's get this matter of 1st, 2nd and 3rd If fingernails would catch on non-matching edges. Of running my fingers over mating edges of frame and grip frame to see Them but looked before leaping (in other words, seen and handled before I was soĭisappointed I gave it away a few years later.īut being such an avid SAA fan I still indulged myself in buying The hammer was a wobbly fit in its recess. Minute crack, its hard rubber grips were far from fitting the grip frameĪnd the entire left side of the grip frame hung past the left side of There was no chance for examination beforehand. 45 with 7-1/2-inch barrel, acquired in November, 1976, In fact I was one of those early detractors. Generation of Colt Single Action Army production quickly gained one upon Retrieved from Ī bad reputation is a tough thing to overcome, and the 3rd APA style: 3rd Gen 2nd Thoughts: UNLIKE SOME, DUKE HAS NO ISSUE WITH HIS 3RD GENERATION COLT SAA REVOLVERS.3rd Gen 2nd Thoughts: UNLIKE SOME, DUKE HAS NO ISSUE WITH HIS 3RD GENERATION COLT SAA REVOLVERS." Retrieved from 2018 Publishers' Development Corporation 26 Oct.

#Colt saa 3rd generation serial numbers free